GeoNode Project¶
Overview¶
The following steps will guide you to a new setup of GeoNode Project. All guides will first install and configure the system to run it in DEBUG
mode (also known as DEVELOPMENT
mode) and then by configuring an HTTPD server to serve GeoNode through the standard HTTP
(80
) port.
Those guides are not meant to be used on a production system. There will be dedicated chapters that will show you some hints to optimize GeoNode for a production-ready machine. In any case, we strongly suggest to task an experienced DevOp or System Administrator before exposing your server to the WEB
.
Ubuntu 20.04¶
This part of the documentation describes the complete setup process for GeoNode on an Ubuntu 20.04 64-bit clean environment (Desktop or Server). All examples use shell commands that you must enter on a local terminal or a remote shell. - If you have a graphical desktop environment you can open the terminal application after login; - if you are working on a remote server the provider or sysadmin should has given you access through an ssh client.
Install the dependencies¶
In this section, we are going to install all the basic packages and tools needed for a complete GeoNode installation. To follow this guide, a piece of basic knowledge about Ubuntu Server configuration and working with a shell is required. This guide uses vim
as the editor; fill free to use nano
, gedit
or others.
Upgrade system packages¶
Check that your system is already up-to-date with the repository running the following commands:
sudo apt update
Create a Dedicated User¶
In the following steps a User named geonode
is used: to run installation commands the user must be in the sudo
group.
Create User geonode
if not present:
# Follow the prompts to set the new user's information.
# It is fine to accept the defaults to leave all of this information blank.
sudo adduser geonode
# The following command adds the user geonode to group sudo
sudo usermod -aG sudo geonode
# make sure the newly created user is allowed to login by ssh
# (out of the scope of this documentation) and switch to User geonode
su geonode
Packages Installation¶
Add the Ubuntu GIS packages prior to installing the other system packages.
sudo add-apt-repository ppa:ubuntugis/ppa
sudo apt update
Note
You don’t need to install the system packages if you want to run the project using Docker
First, we are going to install all the system packages needed for the GeoNode setup.
# Install packages from GeoNode core
sudo apt install -y python3-gdal=3.3.2+dfsg-2~focal2 gdal-bin=3.3.2+dfsg-2~focal2 libgdal-dev=3.3.2+dfsg-2~focal2
sudo apt install -y python3-pip python3-dev python3-virtualenv python3-venv virtualenvwrapper
sudo apt install -y libxml2 libxml2-dev gettext
sudo apt install -y libxslt1-dev libjpeg-dev libpng-dev libpq-dev libmemcached-dev
sudo apt install -y software-properties-common build-essential
sudo apt install -y git unzip gcc zlib1g-dev libgeos-dev libproj-dev
sudo apt install -y sqlite3 spatialite-bin libsqlite3-mod-spatialite
# Install Openjdk
sudo -i apt update
sudo apt install openjdk-8-jdk-headless default-jdk-headless -y
# Remember to select the correct java version /usr/lib/jvm/java-8-openjdk-amd64/jre/bin/java
sudo update-alternatives --config java
sudo apt update -y
sudo apt autoremove -y
sudo apt autoclean -y
sudo apt purge -y
sudo apt clean -y
# Install Packages for Virtual environment management
sudo apt install -y virtualenv virtualenvwrapper
# Install text editor
sudo apt install -y vim
Geonode Project Installation¶
Geonode project is the proper way to run a customized installation of Geonode. The repository of geonode-project contains a minimal set of files following the structure of a django-project. Geonode itself will be installed as a requirement of your project. Inside the project structure is possible to extend, replace or modify all geonode components (e.g. css and other static files, templates, models..) and even register new django apps without touching the original Geonode code.
Note
You can call your geonode project whatever you like following the naming conventions for python packages (generally lower case with underscores (_). In the examples below, replace my_geonode
with whatever you would like to name your project.
See also the README file on geonode-project repository
First of all we need to prepare a new Python Virtual Environment
Prepare the environment
sudo mkdir -p /opt/geonode_custom/
sudo usermod -a -G www-data geonode
sudo chown -Rf geonode:www-data /opt/geonode_custom/
sudo chmod -Rf 775 /opt/geonode_custom/
Clone the source code
cd /opt/geonode_custom/
git clone https://github.com/GeoNode/geonode-project.git -b 4.1.x
Make an instance out of the Django Template
Note
We will call our instance my_geonode
. You can change the name at your convenience.
vim ~/.bashrc
# add the following line to the bottom
source /usr/share/virtualenvwrapper/virtualenvwrapper.sh
source /usr/share/virtualenvwrapper/virtualenvwrapper.sh
mkvirtualenv --python=/usr/bin/python3 my_geonode
Alterantively you can also create the virtual env like below
python3.8 -m venv /home/geonode/dev/.venvs/my_geonode
source /home/geonode/dev/.venvs/my_geonode/bin/activate
pip install Django==3.2.13
django-admin startproject --template=./geonode-project -e py,sh,md,rst,json,yml,ini,env,sample,properties -n monitoring-cron -n Dockerfile my_geonode
# Install the Python packages
cd /opt/geonode_custom/my_geonode
pip install -r src/requirements.txt --upgrade
pip install -e src/ --upgrade
# Install GDAL Utilities for Python
pip install pygdal=="`gdal-config --version`.*"
# Dev scripts
mv .override_dev_env.sample src/.override_dev_env
mv src/manage_dev.sh.sample src/manage_dev.sh
mv src/paver_dev.sh.sample src/paver_dev.sh
Install and Configure the PostgreSQL Database System¶
In this section we are going to install the PostgreSQL
packages along with the PostGIS
extension. Those steps must be done only if you don’t have the DB already installed on your system.
# Ubuntu 20.04
sudo sh -c 'echo "deb http://apt.postgresql.org/pub/repos/apt/ `lsb_release -cs`-pgdg main" >> /etc/apt/sources.list.d/pgdg.list'
sudo wget --no-check-certificate --quiet -O - https://www.postgresql.org/media/keys/ACCC4CF8.asc | sudo apt-key add -
sudo apt update -y; sudo apt install -y postgresql-13 postgresql-13-postgis-3 postgresql-13-postgis-3-scripts postgresql-13 postgresql-client-13
We now must create two databases, my_geonode
and my_geonode_data
, belonging to the role my_geonode
.
Warning
This is our default configuration.
You can use any database or role you need.
The connection parameters must be correctly configured on settings
, as we will see later in this section.
Databases and Permissions¶
First, create the geonode user. GeoNode is going to use this user to access the database
sudo service postgresql start
sudo -u postgres createuser -P my_geonode
# Use the password: geonode
You will be prompted asked to set a password for the user. Enter geonode as password.
Warning
This is a sample password used for the sake of simplicity. This password is very weak and should be changed in a production environment.
Create database my_geonode
and my_geonode_data
with owner my_geonode
sudo -u postgres createdb -O my_geonode my_geonode
sudo -u postgres createdb -O my_geonode my_geonode_data
Next let’s create PostGIS extensions
sudo -u postgres psql -d my_geonode -c 'CREATE EXTENSION postgis;'
sudo -u postgres psql -d my_geonode -c 'GRANT ALL ON geometry_columns TO PUBLIC;'
sudo -u postgres psql -d my_geonode -c 'GRANT ALL ON spatial_ref_sys TO PUBLIC;'
sudo -u postgres psql -d my_geonode -c 'GRANT ALL PRIVILEGES ON ALL TABLES IN SCHEMA public TO my_geonode;'
sudo -u postgres psql -d my_geonode_data -c 'CREATE EXTENSION postgis;'
sudo -u postgres psql -d my_geonode_data -c 'GRANT ALL ON geometry_columns TO PUBLIC;'
sudo -u postgres psql -d my_geonode_data -c 'GRANT ALL ON spatial_ref_sys TO PUBLIC;'
sudo -u postgres psql -d my_geonode_data -c 'GRANT ALL PRIVILEGES ON ALL TABLES IN SCHEMA public TO my_geonode;'
Final step is to change user access policies for local connections in the file pg_hba.conf
sudo vim /etc/postgresql/13/main/pg_hba.conf
Scroll down to the bottom of the document. We want to make local connection trusted
for the default user.
Make sure your configuration looks like the one below.
...
# DO NOT DISABLE!
# If you change this first entry you will need to make sure that the
# database superuser can access the database using some other method.
# Noninteractive access to all databases is required during automatic
# maintenance (custom daily cronjobs, replication, and similar tasks).
#
# Database administrative login by Unix domain socket
local all postgres trust
# TYPE DATABASE USER ADDRESS METHOD
# "local" is for Unix domain socket connections only
local all all md5
# IPv4 local connections:
host all all 127.0.0.1/32 md5
# IPv6 local connections:
host all all ::1/128 md5
# Allow replication connections from localhost, by a user with the
# replication privilege.
local replication all peer
host replication all 127.0.0.1/32 md5
host replication all ::1/128 md5
Warning
If your PostgreSQL
database resides on a separate/remote machine, you’ll have to allow remote access to the databases in the /etc/postgresql/13/main/pg_hba.conf
to the geonode
user and tell PostgreSQL to accept non-local connections in your /etc/postgresql/13/main/postgresql.conf
file
Restart PostgreSQL to make the change effective.
sudo service postgresql restart
PostgreSQL is now ready. To test the configuration, try to connect to the geonode
database as geonode
role.
psql -U postgres my_geonode
# This should not ask for any password
psql -U my_geonode my_geonode
# This should ask for the password geonode
# Repeat the test with geonode_data DB
psql -U postgres my_geonode_data
psql -U my_geonode my_geonode_data
Run GeoNode Project for the first time in DEBUG Mode¶
Warning
Be sure you have successfully completed all the steps of the section Install the dependencies.
This command will run both GeoNode and GeoServer locally after having prepared the Spatialite database. The server will start in DEBUG
(or DEVELOPMENT
) mode, and it will start the following services:
GeoNode on
http://localhost:8000/
GeoServer on
http://localhost:8080/geoserver/
This modality is beneficial to debug issues and/or develop new features, but it cannot be used on a production system.
# Prepare the GeoNode Spatialite database (the first time only)
cd src/
chmod +x paver_dev.sh
./paver_dev.sh setup
./paver_dev.sh sync
Note
In case you want to start again from a clean situation, just run
./paver_dev.sh reset_hard
Warning
This will blow up completely your local_settings
, delete the SQLlite database and remove the GeoServer data dir.
# Run the server in DEBUG mode
./paver_dev.sh start
Once the server has finished the initialization and prints on the console the sentence GeoNode is now available.
, you can open a browser and go to:
http://localhost:8000/
Sign-in with:
user: admin
password: admin
From now on, everything already said for GeoNode Core (please refer to the section 3. Postgis database Setup and following), applies to a GeoNode Project.
Be careful to use the new paths and names everywhere:
Everytime you’ll find the keyword
geonode
, you’ll need to use your geonode custom name instead (in this examplemy_geonode
).Everytime you’ll find paths pointing to
/opt/geonode/
, you’ll need to update them to point to your custom project instead (in this example/opt/geonode_custom/my_geonode
).
Docker¶
Warning
Before moving with this section, you should have read and clearly understood the INSTALLATION > GeoNode Core
sections, and in particular the Docker
one. Everything said for the GeoNode Core Vanilla applies here too, except that the Docker container names will be slightly different. As an instance if you named your project my_geonode
, your containers will be called:
'django4my_geonode' instead of 'django4geonode' and so on...
Deploy an instance of a geonode-project Django template with Docker on localhost¶
Prepare the environment
sudo mkdir -p /opt/geonode_custom/
sudo usermod -a -G www-data geonode
sudo chown -Rf geonode:www-data /opt/geonode_custom/
sudo chmod -Rf 775 /opt/geonode_custom/
Clone the source code
cd /opt/geonode_custom/
git clone https://github.com/GeoNode/geonode-project.git -b 4.1.x
Make an instance out of the Django Template
Note
We will call our instance my_geonode
. You can change the name at your convenience.
source /usr/share/virtualenvwrapper/virtualenvwrapper.sh
mkvirtualenv --python=/usr/bin/python3 my_geonode
Alterantively you can also create the virtual env like below
python3.8 -m venv /home/geonode/dev/.venvs/my_geonode
source /home/geonode/dev/.venvs/my_geonode/bin/activate
pip install Django==3.2.13
django-admin startproject --template=./geonode-project -e py,sh,md,rst,json,yml,ini,env,sample,properties -n monitoring-cron -n Dockerfile my_geonode
cd /opt/geonode_custom/my_geonode
Create the .env file
An .env file is requird to run the application. It can be created from the .env.sample either manually or with the create-envfile.py script.
The script accepts several parameters to create the file, in detail:
hostname: e.g. master.demo.geonode.org, default localhost
https: (boolean), default value is False
email: Admin email (this is required if https is set to True since a valid email is required by Letsencrypt certbot)
emv_type: prod, test or dev. It will set the DEBUG variable to False (prod, test) or True (dev)
geonodepwd: GeoNode admin password (required inside the .env)
geoserverpwd: Geoserver admin password (required inside the .env)
pgpwd: PostgreSQL password (required inside the .env)
dbpwd: GeoNode DB user password (required inside the .env)
geodbpwd: Geodatabase user password (required inside the .env)
clientid: Oauth2 client id (required inside the .env)
clientsecret: Oauth2 client secret (required inside the .env)
secret key: Django secret key (required inside the .env)
sample_file: absolute path to a env_sample file used to create the env_file. If not provided, the one inside the GeoNode project is used.
file: absolute path to a json file that contains all the above configuration
Note
if the same configuration is passed in the json file and as an argument, the CLI one will overwrite the one in the JSON file. If some value is not provided, a random string is used
Example USAGE
```bash
python create-envfile.py -f /opt/core/geonode-project/file.json \
--hostname localhost \
--https \
--email random@email.com \
--geonodepwd gn_password \
--geoserverpwd gs_password \
--pgpwd pg_password \
--dbpwd db_password \
--geodbpwd _db_password \
--clientid 12345 \
--clientsecret abc123
```
Example JSON expected:
```JSON
{
"hostname": "value",
"https": "value",
"email": "value",
"geonodepwd": "value",
"geoserverpwd": "value",
"pgpwd": "value",
"dbpwd": "value",
"geodbpwd": "value",
"clientid": "value",
"clientsecret": "value"
}
```
Modify the code and the templates and rebuild the Docker Containers
docker-compose -f docker-compose.yml build --no-cache
Finally, run the containers
docker-compose -f docker-compose.yml up -d
Deploy an instance of a geonode-project Django template with Docker on a domain¶
Note
We will use www.example.org
as an example. You can change the name at your convenience.
Stop the containers
cd /opt/geonode_custom/my_geonode
docker-compose -f docker-compose.yml stop
Edit the ENV
override file in order to deploy on www.example.org
Replace everywhere localhost
with www.example.org
vim .env
# e.g.: :%s/localhost/www.example.org/g
Note
It is possible to override here even more variables to customize the GeoNode instance. See the GeoNode Settings
section in order to get a list of the available options.
Run the containers in daemon mode
docker-compose -f docker-compose.yml -f docker-compose.override.example-org.yml up --build -d
Test geonode-project with vagrant¶
Note
Inside geonode-project files you will find one file named Vagrantfile.compose and one named Vagrantfile.stack, copy one of them onto file Vagrantfile to use them with vagrant.
apt-get install -y vagrant
#choose what to test (in this case docker-compose.yml)
cp Vagrantfile.compose Vagrantfile
#this will start a vargant virtual machine, generate and build geonode-project
vagrant up
# check services are up upon reboot
vagrant ssh geonode-compose -c 'docker ps'
vagrant destroy -f
# test docker swarm
cp Vagrantfile.stack Vagrantfile
vagrant up
# check services are up upon reboot
vagrant ssh geonode-vagrant -c 'docker service ls'
vagrant destroy -f
Note
Vagrant will generate a dummi project named “antani” inside vagrant, starting with the geonode-project codebase, this way it is possible to test inside vagrant almost instantly what one modifies into geonode-project